SUT800C is a portable, digital ultrasonic flaw detector, capable of quick and easy, no damage, precisely conduct a variety of defects (cracks, inclusions, porosity, etc.) to detect, locate, assess and diagnose internal parts. Functional use of this instrument is widely used in: laboratory, engineering field testing around CSEI, schools and scientific research units, construction quality inspection station, boiler and pressure vessel manufacturing, power industry, engineering machinery manufacturing, iron and steel metallurgy, steel manufacturing , shipbuilding, oil and gas equipment manufacturing, and other areas need to defect detection and quality control, is also widely used in military, aerospace, rail transportation and other areas of in-service safety inspection and life assessment. Works SUT800C ultrasonic flaw is the use of the material in the physical characteristics of ultrasound propagation, reflection and attenuation to discover a defect detection method with high sensitivity, detection speed, low cost, easy operation, high detection thickness of the body and environmentally sound, especially for cracks, lack of fusion defects and other dangerous high detection sensitivity advantages of fast, portable, non-invasive, accurate to detect, locate, evaluate the diagnostic variety of defects within the workpiece. Working conditions Ambient temperature: (-20 ~ 70) ℃ Relative humidity: (20 ~ 95)% RH technical parameters ◆ Detection range: (0 ~ 6000) mm (steel, longitudinal wave), can be adjusted continuously ◆ Operating frequency: (0.2 ~ 20) MHz ◆ Velocity range: (300 ~ 15000) m / s ◆ Dynamic Range: ≥36dB ◆ vertical linearity error: ≤2.5% ◆ level linearity error: ≤0.1% ◆ Resolution:> 40dB (5P14) ◆ sensitivity I volume:> 65dB (deep 200mmФ2 flat bottom hole) ◆ Digital inhibition: (0 to 80)%, does not affect the linearity and gain ◆ electrical noise level: ≤8% ◆ probe types: straight probes, oblique probe, duals, wear ◆ probe through the gate: the door into the wave, lost wave gate; single gate, double gate reading; peak trigger edge trigger. ◆ Alarm: beep alarm, LED light alarm ◆ Power supply: DC (DC) 9V; lithium battery, can work continuously for more than 8 hours ◆ Dimensions: 280mm × 220mm × 70mm ◆ LCD Resolution: 320 * 240 ◆ Note : The index is at the probe frequency of 2.5MHz, detection method for the case of full-wave measured. Instrument features ◆ IP65 protection grade, waterproof, oil, dust-proof design. ◆ Chinese display, master-slave menu, shortcut keys and the design and digital jog wheel spin, easy operation, the technology leader (shortcut keys and digital jog wheel spin combination of the two operations is no other manufacturers, and is ideal for engineers on-site convenient operation, eliminating the tedious single market operation buttons). ◆ Compatible with a variety of probes: probe straight series, oblique probe series duals series, penetration testing series, four kinds of series of different specifications of the probe, fast and accurate. ◆ Full digital true color LCD display (TFT), and waveform display interface is more delicate and humane. Can select a background color according to the environment and the waveform color LCD brightness can be set freely. ◆ High-performance security battery module for easy removal, high-capacity high-performance lithium-ion battery module make the instrument continuously extended to more than ten hours (while charging can be used to meet the overload detection work). ◆ Built common industry testing standards, direct calls, convenient and fast. ◆ light and small portable instrument, which can be gripped with one hand, a unique suspension design, easy high-altitude testing operations, durable, lead the industry trend. ◆ two-dimensional B-scan, real-time scanning, the cross-section display can show the shape of the workpiece defects, making detection results more intuitive. ◆ instrument supports the testing process into the video store recorded files are saved to the built-in memory card. Video files can be played back through the instrument can also be uploaded to a computer for playback via special software. Maximum support 100 video files, with a total length of maximum recording time is 10 hours. The process of recording and playback testing, learning provides a great convenience for testing, but also facilitate the testing process to save for later analysis. ◆ Performance: Calculation and Φ values, not AVG curve, with the end of wave gain law Φ value and achieve dual-modulus, easy to operate. Correction curve, the curved surface to facilitate testing, do not display defects circumferential position. Built-in industry standard, making it easier for beginners. Grid lines can be removed, to avoid overlap with the injury wave, easy to observe the graphics. Echo encoding can better distinguish primary wave, the second wave, convenient testing. Weld illustration shows that make testing more intuitive. B-scan powerful avoid missed. Storage, enabling a mass storage, easy to store more data. The highest sensitivity in the industry. Operating methods and precautions ◆ surface temperature can not overheat, should be less than 120 ℃. ◆ surface roughness can not be too large, otherwise it will affect the testing results. Measured surface of the workpiece to be exposed metallic luster, and flat and smooth. ◆ the workpiece surface required an appropriate amount of coupling agent is applied, in order to facilitate detection. ◆ Probe preparation: Before the instrument starts, depending on the nature of the workpiece shape, defects to select the appropriate probe, the probe tip is coupled to the instrument probe socket. ◆ Select instrument system status. Emission detectors, the receiving system in which different combinations of state for different detection tasks. For specific requirements, select a combination of a certain state, will play optimization echo waveform, to improve signal to noise ratio, to obtain a better resolution of action or optimal detection sensitivity. ◆ Before testing, the instrument must be calibrated probe parameters. ◆ probe connection, communication cables and avoid twisting stress, plug the cable connection at the time, should seize the root of the plug, not seize the cable pull, or drag plug. ◆ When the button operation, not too much force, should not use too much oil and mud stained hands to operate the instrument keyboard, so as not to affect the life of the keyboard. Care and maintenance Important instrument: 1. Please check carefully whether the random information is complete, the resulting instruments and accessories are consistent with the packing list, if there is something wrong, please contact me. Please carefully read the relevant information of the instrument to ensure that you get the rights and services. 2. If the accident occurred in the instrument during use, causing the instrument abnormal situation, is not working, you can turn off the instrument with the battery connector (the battery switch in the "OFF"), and wait for one minute and then re-boot. 3. My company on this instrument provides two-year warranty and lifetime maintenance services. Equipment maintenance matters, please contact me or equipment dealers, not recommended for self-repair. Applications XUT800C ultrasonic flaw PC, data processing software DataPro software is a digital ultrasonic flaw detector communications software, the software runs under MS Windows system, you can connect via USB communication interface with the instrument, read the waveform and parameters stored in the instrument, and gives an intuitive graphical display; waveforms and data can be stored in the database, and can be called up or delete database stored measurement data; data output can be connected with a computer printer. Metrology instrument shows the current flaw metrology generally use "ultrasonic flaw detector test device" to check (provided by the China Academy of test production). When the test needs to be input of the transmitter and instrument calibration device is connected, the output of the receiver is connected with the test device. The instrument is as follows: 1, set the probe type for duals, method: Select the type of probe calibration parameters → Probe → items, rotate the knob, change the probe type for duals. 2, if the output frequency calibration device is 2.5MHz, the instrument also need to probe frequency 2.5MHz. Similarly, the test device is set to output frequency 5MHz or 10MHz, also need to change the instrument's probe corresponding frequency parameter. The instrument will automatically set the appropriate filter parameters to probe frequency band. 3, adjusting verification device, so that the output signal wave appears on the instrument screen. Then adjust the instrument display panning detection range, if necessary, re-adjust the test device "GD" knob, so the leading edge of the signal wave just six horizontal scale alignment instrument first 0,2,4,6,8,10 grid, Test performance level linearity errors. Note: Recommended settings: probe frequency is set to 2.5MHz. If the instrument battery is low, it will affect the performance of the test when, under conditions sufficient power to test or direct plug in the power adapter. Copyright 2012 -? 2014 Xing Billiton Songyuan Copyright Beijing ICP No. 14009359 flaw call customer service immediately free online consultation sales 10:11:40 Welcome! I was online consultancy firm, is pleased to serve you! Sales Sales 10:12:24 10:11:52 Hello, what can help your sales 10:14:06 been a long time did not receive your message, you have other needs my service it? Sales 10:15:48 been a long time did not receive your message, you have other needs my service it? Export chats provider Baidu Bridge